Browsing Mechanical Engineering by Title
Now showing items 177-196 of 465
-
Experimental and numerical investigation of inlet temperature effect on convective heat transfer of γ-Al2O3/Water nanofluid flows in microtubes
(Taylor & Francis, 2019-06-15)Nanofluids are the combination of a base fluid with nanoparticles with sizes of 1–100 nm. In order to increase the heat transfer performance, nanoparticles with higher thermal conductivity compared to that of base fluid ... -
Experimental and numerical modal characterization for additively manufactured triply periodic minimal surface lattice structures: Comparison between free-size and homogenization-based optimization methods
(Wiley, 2023-06)Homogenization-based topology optimization (HMTO) is one of the most extensively used grading methods to generate functionally graded lattice structures (FGLs). However, it requires a precharacterization of the lattices, ... -
Experimental and numerical study of rubber flow in the extrusion die of a weather strip
(Society of Chemical Engineers, 2019)Extrusion is the main method used to produce rubber weather strips in automotive industries, and the quality of the final product largely depends on the thermal properties of the process output. Therefore, precise thermal ... -
An experimental and theoretical analysis of vapor-to-liquid phase change on microstructured surfaces
(Elsevier, 2020-09)In this work, an experimental and a theoretical study was carried out on condensation heat transfer on vertically aligned bare unstructured, micro V-grooved and square-grooved copper substrates. During the experiments, ... -
An experimental investigation into frost accumulation over vertical finned and unfinned surfaces during impinging air flow
(ASME, 2020)Frost formation on evaporators negatively affects the cooling performance of refrigerators. It increases the thermal resistance between the refrigerant and air leading to a reduction in the system cooling capacity. In this ... -
An experimental study of impinging synthetic jets for heat transfer augmentation
(World Scientific Publishing Co, 2015-07)According to recent trends in the field of miniature electronics, the need for compact cooling solutions compatible with very thin profiles and small footprint areas is inevitable. Impinging synthetic jets are recognized ... -
Experimental study on heat transfer of multi-walled carbon nanotubes/water nanofluids in horizontal microtubes
(ASME, 2016)In this study, heat transfer characteristics of multi-walled carbon nanotube based nanofluids were investigated in horizontal microtubes with outer and inner diameters of ∼1067 and ∼889 μm, respectively. Carbon nanotubes ... -
An experimental study on the frost formation over a flat plate: Effect of frosting on heat transfer
(Elsevier, 2023-06-01)Frost accumulation on cooled surfaces generates thermal barrier between the surface and air. Apart from the frost layer thickness, the thermal properties of the frost also affect its heat transfer characteristics. In this ... -
An experimental study on the heat transfer and wettability characteristics of micro-structured surfaces during water vapor condensation under different pressure conditions
(Elsevier, 2021-01)In this study, condensation characteristics of water vapor on micro-structured surfaces at different pressures and subcooling temperature has been investigated experimentally. This work represents a basic study in order ... -
Exploring the performance limits of MOF/polymer MMMs for O2/N2 separation using computational screening
(Elsevier, 2021-01-15)Air separation is one of the most challenging separations because of the very similar molecular dimensions of gas molecules. We used a high-throughput computational screening approach to identify the upper performance ... -
Fabrication and mechanical characterization of polypropylene clay nanocomposites
(Trans Tech Publications Ltd, 2021)Investigating the influence of process parameters is vital to enhance the mechanical properties of nanoparticle reinforced polymer composites. Nanocomposites of polypropylene/nanoclay are prepared by the extrusion method. ... -
Fast and efficient terrain-aware motion planning for exploration rovers
(IEEE, 2021)This paper presents a fast, energy-efficient, and low computational cost traversal solution on sloped terrain. The use of grid-based search algorithms requires high computational power and takes a long time because almost ... -
Fatigue behavior of friction stir welded joints of pure copper with ultra-fine grains
(Elsevier, 2015)In order to determine the long term durability of friction stir welded joints with ultra-fine grained microstructure, investigation of the mechanical response with specific emphasis on fatigue behaviour is critical. In ... -
Fatigue characteristics of continuous welded rails and the effect of residual stress on fatigue-ratchetting interaction
(Taylor & Francis, 2020-03-16)The importance of ratchetting-fatigue interaction is garnering interest due to complex failure mechanism of rail welds under cyclic loading. The objective of this paper is to investigate the fatigue characteristics of ... -
First-principle diffraction simulations as a tool to solve the nanodiffraction problem
(International Union of Crystallography, 2021-08)N/A -
Flow and heat transfer study of an impinging piezoelectric fan over a vertical surface
(ASME, 2016)Piezoelectric fans are low-form-factor cooling devices, which have gained recent attention for electronics cooling. These devices feature a vibrating blade, which sheds vortices from its tip during its motion. The performance ... -
Flow visualization and LES simulations inside a chevron type plate heat exchanger
(Begell House Inc., 2018)An up-scaled model of a single channel of CPHE was used under dynamically similar conditions for the experiments. In experiments, pressure drop measurements and flow visualizations were conducted with aluminum flitter and ... -
Fluid flow characteristics inside convergent, divergent and straight open-end pressure swirl atomizer
(Europe, Institute for Liquid Atomization and Spray Systems, ILASS, 2020)Effects of geometrical parameters on the performance of small-scale open-end pressure swirl atomizers (PSA) have been studied using computational fluid dynamics. The shape of the swirl chamber is the main geometrical feature ... -
Force reference extraction via human interaction for a robotic polishing task: Force-induced motion
In this paper, a method to control a manipulator using force-induced trajectory is proposed. The trajectory is learned from an operator doing the polishing task using a tool attached to the robot's end-effector. The learning ... -
Formation of nano-sized compounds during friction stir welding of Cu–Zn alloys: effect of tool composition
(Elsevier, 2020-12)For the first time, the origin of tool composition effect on microstructure and mechanical properties of the friction stir welded joints has been disclosed. For this aim, nanoindentation, orientation image microscopy, and ...
Share this page