Browsing Mechanical Engineering by Title
Now showing items 121-140 of 465
-
The effect of curvic coupling joints on the roto rdynamic characteristics of gas turbines with tie-shaft
(Canadian Acoustical Association, 2019)The importance and use of curvic coupling joints are garnering interest in many aero-engine rotordynamics applications thanks to their benefits such as lower stress, higher service life, reliable positioning, precise ... -
Effect of different surface treatments on retention of cement-retained, implant-supported crowns
(Quintessence Publishing Co. Inc., 2023)To evaluate the effect of different treatments applied to titanium implant abutment surfaces on the retention of implant-supported crowns retained using resin cement. Materials and Methods: A total of 72 titanium implant ... -
Effect of direct liquid cooling on light emitting diode local hot spots: Natural convection immersion cooling
(Begell House Inc., 2014)The increased popularity of solid state systems with the technological developments have led them to be a favorable choice for many lighting applications besides electronics. However, the development of denser high lumen ... -
Effect of direct liquid cooling on the light emitting diode local hot spots? A computational and experimental study
(Begell House Inc, 2014)The increased popularity of solid state systems with the technological developments have led them to be a favorable choice for many lighting applications besides electronics. However, the development of denser high lumen ... -
Effect of electrostatic stabilization on thermal radiation transfer in nanosuspensions: Photo-thermal energy conversion applications
(Elsevier, 2018-04)Solar thermal collectors are among the most important photo-thermal energy conversion systems. Effectiveness of these systems is measured by the ability of working fluid to absorb incident radiative energy. Although ... -
Effect of external stress on the post-aging mechanical properties of rolled magnesium alloys
(TANGER Ltd., 2020)In the current study the effects of conventional aging and stress aging on the microstructure and mechanical behavior of warm rolled AZ31 magnesium alloy were investigated. Tensile experiments revealed that the ultimate ... -
Effect of friction stir processing on the fatigue performance of AZ31 magnesium alloy
(Wiley, 2023-05)Herein, the cyclic mechanical behavior of AZ31 magnesium alloy after multipass friction stir processing (FSP) is investigated up to the very high-cycle fatigue (VHCF) regime. The grain refinement and texture evolution after ... -
Effect of fuel choice on conductivity and morphological properties of samarium doped ceria electrolytes for IT-SOFC
(TÜBİTAK, 2021)The present investigation is emphasized on the effect of various combustion agents on the crystal properties, surface microstructure, and oxygen ion conductivity of 20% mole-Sm doped ceria (Ce0.80Sm0.20O1.90/SDC20) ceramics ... -
Effect of grain size on the very high cycle fatigue behavior and notch sensitivity of titanium
(Elsevier, 2019-12)The very high-cycle fatigue performances of coarse-grained and ultrafine-grained titanium samples with different geometries at ambient temperature and various stress amplitudes were investigated. Severe plastic deformation ... -
Effect of heat treatment on the corrosion-fatigue of NiTi shape memory alloy
(American Institute of Physics Inc., 2019)Nickel Titanium (NiTi) shape memory alloys have been considered convenient implant material due to their distinguished properties including superelasticity (SE), shape memory effect (SME) and biocompatibility. Among these ... -
The effect of interface gradient distribution on unrealistic flow in 3D droplet simulations
(Europe, Institute for Liquid Atomization and Spray Systems, ILASS, 2021-08-31)The purpose of this study is to investigate the origin of the parasitic current to provide accurate prediction of droplet surface interactions in Volume of Fluid (VOF) framework. The deformation of the droplet due to ... -
The effect of interlaminar graphene nano-sheets reinforced e-glass fiber/ epoxy on low velocity impact response of a composite plate
(IOP Publishing, 2018-05)In this study, we compare the inter-laminar effect of graphene nano-sheets (GNSs) and CNTs on the single and multiple dynamic impact response of E-glass fiber reinforced epoxy composite (GFEP). In the comparisons, raw GFEP ... -
Effect of layer architecture on the mechanical behavior of accumulative roll bonded interstitial free steel/aluminum composites
(Elsevier, 2021-06-22)Multi-layered interstitial free (IF) steel/aluminum (Al) composites were fabricated by the accumulative roll bonding (ARB) method. Two types of IF steel/Al6061 dissimilar layered metal composites (LMC) with varied stacking ... -
The effect of nanoparticle type and nanoparticle mass fraction on heat transfer enhancement in pool boiling
(Elsevier, 2017-06)Determining the heat transfer performance with nanofluids is of cardinal importance in the utilization of nanofluids in thermal systems. This study presents an experimental investigation on nucleate pool boiling heat ... -
Effect of optical design on the thermal management for the smart tv led backlight systems
(IEEE, 2014)Due to recent advances in electronics, lighting and communication technologies, SMART Televisions (TV) have become more affordable, and are rapidly eplacing old-fashioned LCD (liquid crystal display) TV technologies. These ... -
The effect of pH on particle agglomeration and optical properties of nanoparticle suspensions
(Elsevier, 2018-11)Nanoparticle suspensions (NPSs) are used extensively to improve the thermal efficiency of different engineering systems because of their unique thermo-optical properties. NPSs have also been uses in coatings as they improve ... -
Effect of phase change materials on the optical path of LEDs for opto-thermal enhancement
(IEEE, 2023-05)A novel concept based on the encapsulation of transparent phase change materials (PCMs) into the optical packaging structure of light-emitting diodes (LEDs) is presented in this article. The concept was initiated by ... -
Effect of polymer coating on vapor condensation heat transfer
(ASME, 2020-04-01)Condensation heat transfer coefficients (HTCs) are rather low compared to thin film evaporation. Therefore, it can be a limiting factor for designing heat transfer equipment. In this work, heat transfer characteristics of ... -
Effect of processing parameters on the phase transformation of a high temperature copper-based shape memory alloy
(Springer, 2023-11)In the present study, the influence of the processing parameters on the transformation temperatures and microstructural evolution in a copper-based shape memory alloy was investigated. Five times remelting in identical ... -
Effect of processing parameters on the strength of keyhole free friction stir spot aluminum welds
(American Institute of Physics Inc., 2019)Intermediate layer friction stir spot welding (IL-FSSW) is a new solid-state welding method appropriate for making spot joints, particularly in light-weight materials, especially notable on account of the weight saving ...
Share this page