Browsing Mechanical Engineering by Document Type "Article"
Now showing items 61-80 of 263
-
Effect of chemical mechanical polishing on surface nature of titanium implants FT-IR and wettability data of titanium implants surface after chemical mechanical polishing implementation
(Elsevier, 2017)Bioactivity of titanium depends on the quality and characteristics of its surface oxide film. Through implementation of chemical mechanical polishing (CMP) process on titanium plates, a protective oxide (titania) film grows ... -
Effect of commercial purity levels on the mechanical properties of ultrafine-grained titanium
(Elsevier, 2011-03-15)Two grades of commercial purity (CP) titanium (grades 2 and 4) were processed using equal-channel angular extrusion (ECAE) at 300 ◦C and 450 ◦C, respectively. The processing temperatures were the minimum temperatures at ... -
Effect of different surface treatments on retention of cement-retained, implant-supported crowns
(Quintessence Publishing Co. Inc., 2023)To evaluate the effect of different treatments applied to titanium implant abutment surfaces on the retention of implant-supported crowns retained using resin cement. Materials and Methods: A total of 72 titanium implant ... -
Effect of electrostatic stabilization on thermal radiation transfer in nanosuspensions: Photo-thermal energy conversion applications
(Elsevier, 2018-04)Solar thermal collectors are among the most important photo-thermal energy conversion systems. Effectiveness of these systems is measured by the ability of working fluid to absorb incident radiative energy. Although ... -
Effect of friction stir processing on the fatigue performance of AZ31 magnesium alloy
(Wiley, 2023-05)Herein, the cyclic mechanical behavior of AZ31 magnesium alloy after multipass friction stir processing (FSP) is investigated up to the very high-cycle fatigue (VHCF) regime. The grain refinement and texture evolution after ... -
Effect of fuel choice on conductivity and morphological properties of samarium doped ceria electrolytes for IT-SOFC
(TÜBİTAK, 2021)The present investigation is emphasized on the effect of various combustion agents on the crystal properties, surface microstructure, and oxygen ion conductivity of 20% mole-Sm doped ceria (Ce0.80Sm0.20O1.90/SDC20) ceramics ... -
Effect of grain size on the very high cycle fatigue behavior and notch sensitivity of titanium
(Elsevier, 2019-12)The very high-cycle fatigue performances of coarse-grained and ultrafine-grained titanium samples with different geometries at ambient temperature and various stress amplitudes were investigated. Severe plastic deformation ... -
The effect of interlaminar graphene nano-sheets reinforced e-glass fiber/ epoxy on low velocity impact response of a composite plate
(IOP Publishing, 2018-05)In this study, we compare the inter-laminar effect of graphene nano-sheets (GNSs) and CNTs on the single and multiple dynamic impact response of E-glass fiber reinforced epoxy composite (GFEP). In the comparisons, raw GFEP ... -
Effect of layer architecture on the mechanical behavior of accumulative roll bonded interstitial free steel/aluminum composites
(Elsevier, 2021-06-22)Multi-layered interstitial free (IF) steel/aluminum (Al) composites were fabricated by the accumulative roll bonding (ARB) method. Two types of IF steel/Al6061 dissimilar layered metal composites (LMC) with varied stacking ... -
The effect of nanoparticle type and nanoparticle mass fraction on heat transfer enhancement in pool boiling
(Elsevier, 2017-06)Determining the heat transfer performance with nanofluids is of cardinal importance in the utilization of nanofluids in thermal systems. This study presents an experimental investigation on nucleate pool boiling heat ... -
The effect of pH on particle agglomeration and optical properties of nanoparticle suspensions
(Elsevier, 2018-11)Nanoparticle suspensions (NPSs) are used extensively to improve the thermal efficiency of different engineering systems because of their unique thermo-optical properties. NPSs have also been uses in coatings as they improve ... -
Effect of phase change materials on the optical path of LEDs for opto-thermal enhancement
(IEEE, 2023-05)A novel concept based on the encapsulation of transparent phase change materials (PCMs) into the optical packaging structure of light-emitting diodes (LEDs) is presented in this article. The concept was initiated by ... -
Effect of polymer coating on vapor condensation heat transfer
(ASME, 2020-04-01)Condensation heat transfer coefficients (HTCs) are rather low compared to thin film evaporation. Therefore, it can be a limiting factor for designing heat transfer equipment. In this work, heat transfer characteristics of ... -
Effect of processing parameters on the phase transformation of a high temperature copper-based shape memory alloy
(Springer, 2023-11)In the present study, the influence of the processing parameters on the transformation temperatures and microstructural evolution in a copper-based shape memory alloy was investigated. Five times remelting in identical ... -
Effect of purity levels on the high-temperature deformation characteristics of severely deformed titanium
(Springer International Publishing, 2017)In the present investigation, high-temperature compression tests were conducted at strain rates of 0.001 to 0.1 s−1 and at temperatures of 873 K to 1173 K (600 °C to 900 °C) in order to study the hot deformation characteristics ... -
Effect of severe plastic deformation on the damping behavior of titanium
(Elsevier, 2019-06-01)In this work, influence of severe plastic deformation on the damping properties of commercial purity titanium is explored. Deformation induced grain refinement improved the strength at room temperature while this effect ... -
Effect of slurry aging on stability and performance of chemical mechanical planarization process
(Elsevier, 2011-03)Chemical mechanical planarization (CMP) is known to be one of the most challenging processes in microelectronics manufacturing due to the number of variables involved in the design of the process. In particular, the slurries ... -
The effect of spotwelds and structural adhesives on static and dynamic characteristics of vehicle body design
(Sage, 2021-10)Spotwelding and structural adhesive applications are two important processes in the automotive industry as they are closely associated with the functional requirements, weight, and cost of the vehicle. Even though there ... -
Effect of stress aging induced precipitates on corrosion behavior of NiTi shape memory alloys
(Springer, 2021-10)In this study, the influences of the stress aging process on the electrochemical behaviors toward evaluating corrosion resistance of NiTi shape memory alloys in the in-vitro condition have been investigated. For this ... -
Effect of the probe location on the absorption by an array of gold nano-particles on a dielectric surface
(Elsevier, 2017)Effect of silicon atomic force microscope probe position and particle spacing on the local absorption of an array of gold nanoparticles placed over a dielectric borosilicate glass surface are evaluated. An improved, ...
Share this page