Show simple item record

dc.contributor.authorShojaei, Kambiz
dc.date.accessioned2016-10-14T13:28:41Z
dc.date.available2016-10-14T13:28:41Z
dc.date.issued2016-01
dc.identifier.urihttp://hdl.handle.net/10679/4510
dc.identifier.urihttp://discover.ozyegin.edu.tr/iii/encore/record/C__Rb1600044?lang=eng
dc.descriptionThesis (M.A.)--Özyeğin University, Graduate School of Sciences and Engineering, Department of Mechanical Engineering, January 2016.
dc.description.abstractNowadays, aluminum alloys in automotive and aerospace industries have assigned a noticeable portion in structural applications in comparison to many steel alloys. The aim of this study was to investigate the high-temperature deformation behavior and microstructural evolution of Al-Zn-Mg-Cu aluminum alloy for two different annealed and cold rolled conditions. The elevated temperature deformation behavior and microstructural evolution of 7075 aluminum alloy at the annealed and cold rolled conditions have been studied. Isothermal uniaxial tensile tests at different temperatures of ambient temperature, 200, 250, 300 and 350 C and strain rates of 0.001, 0.01, 0.1 s−1 were conducted. The effects of two important factors; deformation temperature and strain rate sensitivity on the tensile deformation behaviors with support of fracture mechanism characteristics are discussed in details. The Zener-Hollomon parameter in an exponenttype equation has been utilized for both tested conditions in order to calculate the activation energy for the studied conditions. The results review indicates that with the increase of deformation temperature or the decrease of strain rate, the fraction of recrystallized grains increases which leads to higher elongation. This is mainly attributed to dynamic recrystallization during the tensile deformation. Accordingly, the maximum UTS value at elevated deformation temperature has been reported 218 MPa in rolled samples at 200 C under the strain rate of 0.1 s−1, whereas the maximum elongation to fracture was 55.9% in rolled samples at 350 C under the strain rate of 0.01 s−1. In addition, unlike annealed condition it has been observed that the cold working has a remarkable effect on increasing the peak stress and also leads to higher ductility at elevated deformation temperatures. But in contrast, at ambient temperature it has been observed that severely cold work could decrease the ductility. However, at 350 C and 0.001 s−1 the general trend of softening has changed and the ductility dropped which could be imputed to the dynamic precipitation resulting in the formation of the secondary phases during high-temperature deformation. Observation of the fracture surfaces in the studied deformation conditions has showed that localized necking caused the final fracture of the specimens in which microvoids can be seen at lower deformation temperatures. Whereas by increasing the deformation temperature coalescence of dimples and micro voids leading to a relatively coarse but less dense morphology resulted in fracture.en_US
dc.description.abstractGünümüzde alüminyum alaşımların çelik alaşımlara oranla otomotiv ve uzay sanayisinin yapısal uygulamalarında daha fazla tercih edildiği görülmektedir. Bu tezde 7075 alüminyum alaşımının tavlanmış ve haddelenmiş durumları altında sıcak sekil değiştirme karakteristiği ve mikro yapısal gelişimi incelenmiştir. Test numuneleri üzerinde farklı çevresel sıcaklıklarda (200, 250, 300 ve 350 C) ve farklı gerinme oranlarında (0.001, 0.01, 0.1 s−1) izotermik tek eksenli çekme testleri gerçekleştirilmistir. Test sonuçları üzerinde iki önemli etken olan sıcaklık ve gerinme oran duyarlılığı kırılma mekanizmaları desteği ile tartışılmıştır. Test edilen durumların aktivasyon enerjilerinin hesaplanabilmesi için örnek denklemlerdeki Zener-Hollomon değişkeninden faydalanılmıştır. Yapılan testlerin sonucunda deformasyon sıcaklığındaki artısın ya da gerinim oranlarındaki azalışın yeniden kristalleşmiş tane oranını arttırdığı görülmüştür. Bu artısın daha fazla uzamaya olanak sağladığı anlaşılmıştır. Bu durumun sebebi olarak çekme deformasyonu sırasındaki dinamik yeniden kristalleşme öngörülmüştür. Dolayısıyla, 200 C ve 0.1 s−1 gerinme oranındaki haddelenmiş numunelerin maksimum UTS degeri 218 MPa olarak ölçülmüştür. Oysa ki 350 C ve 0.01 s−1 gerilme oranına sahip haddelenmiş numunelerin kırılmaya kadar uzama oranı 55.9% olarak ölçülmüştür. Ayrıca tavlamanın aksine soğuk işlemelerin maksimum gerilme değerini arttırdığı ve bu durumunda yüksek deformasyon sıcaklıklarından daha fazla sünekliğe yol açtığı görülmüştür. Tam tersine, ortam sıcaklığında soğuk işlemelerin esnekliği azalttığı gözlemlenmiştir. Ancak 350 C sıcaklık ve 0.001 s−1 gerinme oranında genel yumuşama eğiliminin geliştiği ve sünekliğinin azaldığı görülmüştür. Bu azalış yüksek sıcaklıklardaki deformasyon esnasında oluşan ikincil evrelerdeki dinamik çökelme ile açıklanmaktadır. Çalışılan sekil değiştirme şartlarında incelenen kırılma yüzeyleri ile numunelerde düşük sıcaklık kırılmalarına mikro boşlukların bulunduğu bölgesel boyun vermelerin sebep olduğu anlaşılmıştır. Öte yandan, sıcaklığın artması ile boşlukların birleşmesi sayesinde kırılma meydana gelmiş olup, daha iri ve fakat düşük yoğunluğa sahip bir kırılma morfolojisi ortaya çıkmıştır.
dc.language.isoengen_US
dc.rightsrestrictedAccess
dc.titleAmbient and elevated temperature mechanical behavior of a high strength aluminum alloy after cold deformationen_US
dc.title.alternativeYüksek dayanımlı aluminyum alaşımının soğuk şekil değişim sonrası ortam ve yükseltilmiş sıcaklıkta mekanik davranışı
dc.typeMaster's thesisen_US
dc.contributor.advisorYapıcı, Güney Güven
dc.contributor.committeeMemberYapıcı, Güney Güven
dc.contributor.committeeMemberAtlı, K. C.
dc.contributor.committeeMemberBundur, Zeynep Başaran
dc.publicationstatusunpublisheden_US
dc.contributor.departmentÖzyeğin University
dc.subject.keywordsMaterialsen_US
dc.contributor.ozugradstudentShojaei, Kambiz
dc.contributor.authorMale1
dc.relation.publicationcategoryThesis - Institutional Graduate Student


Files in this item

Thumbnail

This item appears in the following Collection(s)

  • Master's Theses
    This Collection covers master's thesis produced at Özyeğin University

Show simple item record


Share this page