Browsing by Author "Ikhlaq, M."

Now showing 1 - 3 of 3

Metadata only
Acoustics and heat transfer characteristics of piezoelectric driven central orifice synthetic jet actuators
(Taylor & Francis, 2022-09-19) Ikhlaq, M.; Yasir, M.; Ghaffari, O.; Arık, Mehmet; Mechanical Engineering; ARIK, Mehmet
Growth in computational capacity combined with a decrease in the size of digital devices has led to increasing demand for more active and efficient cooling of electronics. In this study, an experimental investigation into two different sizes of central orifice Synthetic Jet Actuators (SJAs) is conducted to evaluate their heat transfer as well as noise generation characteristics. Two SJAs (40 mm and 20 mm) are examined, covering a distinct span of frequencies ranging from low to medium (<5500 Hz) in regards to the effect of SJA size over performance. The SJAs’ disk deflection, structural frequency, and jet exit velocity were measured to fully characterize the jet performance. The maximum Nusselt number for the largest SJA was 3 times more than the smallest SJA, where the evaluation of stroke length suggests no effective synthetic jet formation for the smallest SJA. The noise from the SJAs was measured in an anechoic chamber using three microphones, Fast Fourier Transform (FFT) of the sound pressure levels provide contributions to different tones in the resulting noise. 1/3 Octave Constant Percentage Bandwidth (CPB) analysis was performed to identify the frequency bands making the largest contribution to the noise. The largest SJA showed the highest heat transfer at acceptable noise levels during the operation below resonance frequency.
Metadata only
A computational study on the momentum and heat transfer distribution of a low frequency round impinging synthetic jet
(ASME, 2015) Ikhlaq, M.; Dogruoz, B.; Ghaffari, O.; Arık, Mehmet; Mechanical Engineering; ARIK, Mehmet
Impinging synthetic jets have been considered as a possible solution for cooling miniature structures. It has been shown that synthetic jet performance is sensitive to the distance between the jet nozzle and the target surface where enhancement of heat transfer decreases with a reduction in nozzle-to-target plate distance. At low nozzle-to-target spacing, no detailed information about the momentum and temperature fields have been shown in prior literature, therefore further investigation is needed. In this study, a 3-D computational fluid dynamics model was constructed to determine the flow and temperature fields of a meso-scale synthetic jet at a nozzle-to-target surface spacing of H/D = 2, ReD,j= 1400 and f = 500 Hz. Unlike the majority of previous computational studies, rather than specifying the boundary conditions at the nozzle, the flow inside the synthetic jet device was solved by specifying the time dependent boundary conditions on the vibrating diaphragm and utilizing the moving mesh technique. Local surface pressure and heat transfer coefficient distributions were determined and discussed. It was found that the pulsating flow at the nozzle exit for a round jet generates vortex rings and these rings seem to have some considerable effects on the target surface profiles.
Metadata only
Synthetic jet cooling technology for electronics thermal management - A critical review
(IEEE, 2021-08) Ikhlaq, M.; Yasir, M.; Demiroglu, M.; Arık, Mehmet; Mechanical Engineering; ARIK, Mehmet
Effective removal of excess heat from electronics equipment is the key to its intended functionality. A Defense Advanced Research Projects Agency (DARPA) hard problem is proposed in microtechnologies for the air-cooled heat exchangers (MACE) program that posed challenges to reduce the heat sink size fourfold while using only 50% of the current power budget. While numerous heat removal techniques have been proposed over the last several decades, synthetic jet actuator (SJA) is one of the leading candidates to create a game-changing cooling performance. This is due to its inherent advantages, such as size, low power consumption, ease of use, and affordability. This review article looks at different actuation methods (electromagnetic, piston cylinder, piezoelectric, and so on) to generate synthetic jet cooling. The performances of these approaches vary and need a procedure to unify the predictive capability. The performances are evaluated based on actuation (stroke length, operating frequency, and jet-to-heater spacing) and geometric parameters (shape and size of the cavity and the orifice). The flow characteristics and jet formation criterion are also discussed methods, and a critical commentary is added to normalize previous findings. Available correlations for predicting Nu numbers are evaluated and summarized through data sets for a possible unification. Finally, an empirical correlation is proposed based on available data using nonlinear regression via computational tools. To conclude, the challenges and research gaps are enumerated covering the fundamental and applied aspects of those jets for the implementation in electronics thermal management.